ÆLITEFLO™*/ÆLITEFLOLV
Low Modulus Microhybrid Composite

GENERAL INFORMATION

ÆLITEFLO and ÆLITEFLO LV (Low Viscosity) are light-cured, highly filled microhybrid composites with a low modulus of elasticity. These flowable composites are ideal for Class III, Class V and some smaller Class IV restorations. They may also be used as a cavity liner (Class I or Class II), pit and fissure sealant, for repair of marginal defects, blocking out undercuts, porcelain repairs, porcelain veneer cementation or with splinting materials (e.g., fibers, orthodontic wire). With an average particle size of 0.7 microns, these composites are highly polishable and due to the barium glass filler, they are designed to be radiographically apparent at a greater than 2 mm thickness.

Even though ÆLITEFLO and ÆLITEFLO LV are flowable, their properties prevent them from slumping for better control in hard to access areas. Using the provided tips, these materials are easily injected directly into the cavity preparation and usually can be shaped with the tip itself.

Studies by C. L. Davidson and C. M. Kemp-Scholte¹ have demonstrated that a strong correlation exists between margin failure and Young's modulus of the composite restorative material, especially in a Class V restoration. The higher the modulus of elasticity, the stiffer thematerial, thereby increasing the possibility of margin failure during occlusal loading. The elastic modulus² of dentin is about 18 GPa whereas ÆLITEFLO is about 3.6 GPa, giving it more elastic characteristics. These characteristics compensate for curing contraction stress, reduce the frequency of margin microleakage and possible debonding. This is especially important in restoring patient's dentition with multiple abfraction lesions, where a highly filled stiff composite may ultimately fail.

The principal uses of ÆLITEFLO are:

The principal uses of ÆLITEFLO LV are:
Small Class V
Pit and fissure sealant

Cavity liner (Class I or Class II)

1. Both the ALL-BOND 2 ^®* and ONE-STEP^®* adhesive systems function best in a "moist" environment, therefore a visibly moist surface must be observed. After rinsing the etchant, lightly air dry the preparation. The use of a rehydrating agent such as AQUA-PREP™* F is recommended to ensure proper moisture.

2. Once ÆLITEFLO/ÆLITEFLO LV has been placed and light-cured, it must be finished with discs and/or polishing paste, etc. The restoration may appear smooth and polished immediately after placement, however an oxygen inhibited layer is present and must be removed to prevent staining.

3. Dispose of dispensing tip after each use to avoid cross-contamination.

1. Prior to isolation, select appropriate shade of ÆLITEFLO/ÆLITEFLO LV.

2. Isolate and prepare the tooth in a conservative manner. Clean the entire preparation with a slurry of pumice and a disinfectant, such as CAVITY CLEANSER™*, or water.

3. Etch using an etchant, such as UNI-ETCH^®* or ETCH-37™*, according to manufacturer's instructions.

4. Apply an adhesive, such as ALL-BOND 2, ALL-BOND 3™, ONE-STEP or ONE-STEP PLUS, according to the manufacturer's instructions.

5. Using the previously selected shade, place 1-2 mm increments of composite into the cavity preparation. To prevent excess material extruding from syringe, pull back plunger immediately after the desired amount is dispensed. Light-cure each increment for 20 seconds at 500m/Wcm². Continue to build incrementally until cavity preparation is filled to the cavosurface margin.

6. After finishing and polishing have been completed, apply a surface sealant, such as FORTIFY™* or FORTIFY PLUS, according to manufacturer's instructions.
OR If using BisCover™* LV Liquid Polish, finish and apply BisCover LV according to manufacturer's instructions. This will improve marginal integrity and reduce wear and staining.

STORAGE: Store at room temperature (22°C/72°F). Refer to individual component labels for specific expiration dates.

PRECAUTIONS: Unpolymerized resins may cause skin sensitization in susceptible persons. In case of contact with the skin, wash thoroughly with soap and water.

WARRANTY: BISCO, Inc. recognizes its responsibility to replace products if proven to be defective. BISCO, Inc. does not accept liability for any damages or loss, either direct or consequential, stemming from the use of or inability to use the products as described. Before using, it is the responsibility of the user to determine the suitability of the product for its intended use. The user assumes all risk and liability in connection therewith.

CAUTION: U.S. Federal law restricts this device to sale by or on the order of a dental professional.


* ALL-BOND 2, ONE-STEP and UNI-ETCH are registered trademarks of BISCO, Inc.
ÆLITEFLO, AQUA-PREP, ALL-BOND 3, CAVITY CLEANSER, ETCH-37, FORTIFY and BisCover are trademarks of BISCO, Inc.

1. Kemp-Scholte CM, Davidson CL. Marginal integrity related to bond strength and strain capacity of composite resin restorative systems, J. Prosthet. Dent 1990; 64:(6) 658-664.
2. Craig RG, Peyton FA. Elastic and mechanical properties of human dentin, J. Dent. Res. 1958; 37:(4) 710-718.


BISCO, Inc.
1100 W. Irving Park Rd.
Schaumburg, IL 60193
1-(800)-BIS-DENT
847-534-6000
www.bisco.com

CE ADMINISTRATOR
Bisico France -
Mr. Fred Picavet
L'Opera- BP. 60
13680 Lançon De Provence
France
Phone: 33-490-42-9292
Fax: 33-490-42-9261

IN-036R5
Rev. 8/07

U.S. Patent: 5,865,623