For: Crowns, Bridges, Inlays, and Onlays
Preparation
Procedures
NOTE: BisCem is a self-adhesive cement which does not require etching
or priming of the prepared surfaces.
1. Remove the temporary
restoration and all temporary cement residue.
2. Try-in the final restoration to insure proper fit.
3. Clean the preparation with pumice and water. Rinse
thoroughly.
4. Remove all surface water using a strong stream of
air on the preparation for 3 to 5 seconds. Do not desiccate.
(Protect the preparation from contamination. When applicable,
use of a rubber dam is recommended.)
Cement Mixing
Procedures
1. Remove the syringe
cap from the dual-syringe.
2. Dispense a small amount of material onto a mixing
pad to eliminate any voids in each chamber of the dual-syringe.
3. Attach a mixing tip to the dual-syringe by lining
up the key and keyway. Then turn the brown locking mechanism
clockwise.
4. Pressing the plunger will mix and dispense the BisCem.
(See "TECHNICAL INFORMATION" Section for Working
and Setting Time information.)
Cementation
Procedures
NOTE: For
alumina or zirconia ceramic restorations, sandblast
the internal surfaces for 15 seconds, rinse and dry.
1. Apply cement
to the internal surfaces of the restoration. For inlays,
it may be easier to apply the cement to the tooth preparation.
2. Seat the restoration and remove any excess cement.
HINT: To aid in the removal of excess cement, initially light
cure the margins for 2-3 seconds.
3. Light cure for 20-30 seconds, or allow to self cure. (When using self-cured mode, light curing the
margins even briefly will expedite the final
set.)
For: Posts
(pre-fabricated, metal, cast and non-metal/fiber
posts)
Preparation
Procedures
1. Prepare the post
space per post manufacturer's instruction. Etching and
bonding agents are not required.
2. Size and fit post to insure proper fit.
3. Clean post per manufacturer's instructions.
Cement Mixing
Procedures
1. Remove the syringe
cap from the dual-syringe.
2. Dispense a small amount of material onto a mixing
pad to eliminate any voids in each chamber of the dual-syringe.
3. Attach a mixing tip to the dual-syringe by lining
up the key and keyway. Then turn the brown locking mechanism
clockwise.
4. Pressing the plunger will mix and dispense the BisCem.
(See "TECHNICAL INFORMATION" Section for Working
and Setting Time information.)
Cementation
Procedures
1. Apply cement
to the canal walls using an endodontic file, lentulo
spiral or paper point and coat the post.
2. Seat the post and remove any excess cement. HINT:
To aid in the removal of excess cement, initially light
cure the cement for 2-3 seconds.
3. Light cure for 20-30 seconds, or allow to self cure. (When using self-cured mode, light curing the
margins even briefly will expedite the final
set.)
4. Proceed with core build-up procedure.
STORAGE: Store at room temperature (22°C/72°F).
See individual component labels for specific expiration
dates.
PRECAUTIONS: Unpolymerized resins may cause skin
sensitization in susceptible persons. In case of contact
with the skin, wash thoroughly with soap and water.
WARRANTY: BISCO, Inc. recognizes its responsibility
to replace products if proven to be defective. BISCO,
Inc. does not accept liability for any damages or loss,
either direct or consequential, stemming from the use
of or inability to use the products as described. Before
using, it is the responsibility of the user to determine
the suitability of the product for its intended use.
The user assumes all risk and liabilty in connection
therewith.
CAUTION: U.S. Federal law restricts this device
to sale by or on the order of a dental professional.
*BisCem is a registered trademark of BISCO, Inc.
CHOICE is a trademark of BISCO, Inc.
BISCO, INC.
1100 W. Irving Park Road
Schaumburg, IL 60193
U.S.A.
847-534-6000
1-800-BIS-DENT
www.bisco.com
CE ADMINISTRATOR
Bisico France -
Mr. Fred Picavet
L'Opera- BP. 60
13680 Lançon De Provence
France
Phone: 33-490-42-9292
Fax: 33-490-42-9261
IN-154R2
Rev. 7/07 |
: