1. Light-Cured Base Pastes: Use alone (without catalyst) for cementation of anterior all- ceramic veneers and crowns where ceramic thickness is less than 3 mm. Available in:
   a) Clear: Use to lower the value, in cases where the value of the restoration is slightly too bright.
   b) Milky: Use in most situations.
   c) Opaque: Use to raise the value, where maximum brightness is required.
2. Dual-Cured Clear Catalyst Paste: Mix with an equal amount of Base Paste when a dual-cured composite cement is required. This is recommended for cementation of anterior all-ceramic veneers and crowns where ceramic thickness is greater than 3 mm. This is also recommended for cementation of composite and ceramic inlays, onlays, crowns and fixed partial dentures, unetchable ceramic restorations, as well as gold/metal based inlays, onlays and crowns.
3. Light-Cured Viscosity Modifier: Mix into Base Paste one drop at a time to create a more flowable cement. Do not mix with Try-In Pastes.
4. Light-Cured Color Modifier: Mix this Color Modifier Paste into Base Paste in small increments to customize shade of cement. Do not mix with Try-In Pastes.
5. Light-Cured Pink Block-Out Paste: Mix this Pink Block-Out Paste into Base Paste in small increments to block-out dark teeth. Do not mix with Try-In Pastes.
6. Water-Soluble Try-in Pastes: Available in shades Clear, Milky and Opaque which match light-cured Base Paste shades. Use when trying in anterior all-ceramic veneers and crowns to determine value of Base Paste prior to final cementation. This is a non-polymerizing, water-soluble paste. Use only with water-soluble try-in pastes and do not mix with light-cured materials. Rinse thoroughly from tooth and inside of restoration prior to beginning final cementation procedures.
7. Water-Soluble Color Modifier Try-in Paste: Shade matches corresponding Light-Cured Color Modifier. Use when trying in anterior all-ceramic veneers and crowns to determine custom shading needed with Base Paste prior to final cementation. This is a non-polymerizing, water-soluble paste. Use only with water-soluble try-in pastes and do not mix with light-cured materials. Rinse thoroughly from tooth and inside of restoration prior to beginning final cementation procedures.
8. Water-Soluble Pink Block-Out Try-In Paste: Pink Shade matches corresponding Light-Cured Pink Block-Out Paste. Use when trying in anterior all-ceramic veneers and crowns to determine neutralization needed with Base Paste prior to final cementation. This is a non-polymerizing, water-soluble paste. Use only with water-soluble try-in pastes and do not mix with light-cured materials. Rinse thoroughly from tooth and inside of restoration prior to beginning final cementation procedures.
9. Porcelain Primer: Use on the inside surface of all-ceramic restorations after try-in, prior to final cementation.

1. Try-in the restoration lined with the Water-Soluble Milky Try-In Paste (typically used in the anterior region).
2. Seat the restoration and evaluate.
   a. If the value (opacity) needs to be changed, replace the Milky Shade with:
   • the Clear Shade to slightly lower the value of the restoration.
   • the Opaque Shade to raise the value of the restoration.
   b. If the overall color needs to be altered (warmed eg. changed A2 to A3):
   • add small increments of the Color Modifier Try-In Paste until the desired color is achieved.
   c. If the underlying tooth structure is dark and needs to be blocked-out (neutralized):
   • add small increments of the Pink Block-Out Try-In Paste until the darkness of the underlying tooth is blocked-out.

1. Anesthetize teeth as necessary.
2. Remove provisional, clean the preparation (sandblast or microetch), rinse with water and lightly dry.
3. Try-in the restoration, make necessary adjustments and polish.
4. Etch enamel and dentin using an etchant such as UNI-ETCH^®* for 15 seconds (Do not over-etch). Rinse thoroughly. Remove excess water with a brief burst of air. DO NOT DESICCATE! ONE-STEP/ONE-STEP PLUS (OS/OS+) works best with moist dentin/enamel.
5. Apply two consecutive coats of OS/OS+ to the dentin and enamel without waiting between coats. Air-dry thoroughly for a minimum of 10 seconds to remove and evaporate excess solvent. Surfaces will appear glossy when coverage is sufficient. AVOID POOLING AT INTERNAL LINE ANGLES.
6. Light-cure for 10 seconds per surface.
   Refer to manufacturer's instructions. Not all one-bottle adhesives bond to dual-cured or self-cured composites. Unlike others, ONE-STEP and ONE-STEP PLUS bond to dual-cured and self-cured composites.
   

1. Anesthetize teeth as necessary.
2. Remove provisional, clean the preparation (sandblast or microetch), rinse with water and lightly dry.
3. Try-in the restoration, make necessary adjustments and polish.
4. Etch enamel and dentin using an etchant such as UNI-ETCH for 15 seconds (Do not over-etch). Rinse thoroughly. Remove excess water with a brief burst of air. DO NOT DESICCATE! ALL-BOND 2 works best with moist dentin/enamel.
5. Mix PRIMERS A and B. Apply five consecutive coats to the enamel and dentin. DO NOT DRY BETWEEN COATS! Air dry all surfaces for a minimum of 5-6 seconds with an air syringe to remove and evaporate excess solvent. Properly primed surface will appear glossy when coverage is sufficient. Light cure for 20 seconds.
6. Apply a layer of PRE-BOND™* RESIN immediately prior to cementation. Air thin. DO NOT LIGHT- CURE.
   For Veneer Cementation: Do not use PRE-BOND RESIN . Instead, apply a thin layer of D/E RESIN over enamel/dentin. Air thin. DO NOT LIGHT-CURE.
   

1. Sandblast internal surface of restoration for 1-2 seconds and etch for 3-4 minutes with PORCELAIN ETCHANT (4% hydrofluoric acid gel). Rinse with water and air dry.
   Refer to manufacturer's instructions. Not all ceramic systems are etchable.
2. Apply PORCELAIN PRIMER (silane) to the internal surface for 30 seconds. Dry with air syringe.
3. Apply one coat of OS/OS+. Air dry. Light-cure for 10 seconds.
   or
   Apply a thin layer of D/E RESIN from the ALL-BOND 2 System. Air thin. DO NOT LIGHT-CURE.
   

1. Sandblast internal surface of restoration for 1-2 seconds. Rinse with water and air dry.
2. Apply one coat of OS/OS+. Air dry. Light-cure for 10 seconds.
   or
   Apply a thin layer of D/E RESIN from the ALL-BOND 2 System. Air thin. DO NOT LIGHT- CURE.

1. Select desired opacity of Light-Cured Base Paste (Milky Shade for most situations).
   Optional: Adjust the chroma with small addition of LIGHT-CURED COLOR MODIFIER, if necessary.
   Optional: Neutralize the underlying tooth darkness with small addition of LIGHT-CURED PINK BLOCK-OUT PASTE.
   Optional: Adjust the viscosity with small addition of LIGHT-CURED VISCOSITY MODIFIER, for a more flowable cement.
2. Mix equal amounts of the Base and Catalyst pastes and line the inside surface of the restoration.
3. Seat the restoration with gentle, passive pressure.
4. Remove excess paste from margins immediately.
   Technique tip:
   a. Tack-cure each margin for 4-7 seconds or until excess paste is gelatinous but not fully set.
   b. Carefully trim/skim flash with a #12 blade.
5. Light-cure each surface of the restoration for 40 seconds or longer.

1. Sandblast internal surface of veneer for 1-2 seconds and etch for 3-4 minutes with PORCELAIN ETCHANT (4% hydrofluoric acid gel). Rinse with water and air dry.
   Refer to manufacturer's instructions. Not all ceramic systems are etchable.
2. Apply PORCELAIN PRIMER (silane) to the internal surface for 30 seconds. Dry with air syringe.
3. Apply one coat of OS/OS+. Air dry. Light-cure for 10 seconds.
   or
   Apply thin layer of D/E RESIN from the ALL-BOND 2 System. Air thin. DO NOT LIGHT- CURE.

1. Select desired opacity of Light-Cured Base Paste (Milky Shade for most situations)
   Optional: Adjust the chroma with small addition of LIGHT-CURED COLOR MODIFIER, if necessary.
   Optional: Neutralize the underlying tooth darkness with small addition of LIGHT-CURED PINK BLOCK-OUT PASTE.
   Optional: Adjust the viscosity with small addition of LIGHT-CURED VISCOSITY MODIFIER, for a more flowable cement.
   
2. Line inside of veneer with Base Paste. Do not use Catalyst, only use Light-Cured Base Paste.
3. Seat veneer with gentle, passive pressure.
4. Remove excess paste from margins immediately.
   Technique tip:
   a. Tack-cure each margin for 4-7 seconds or until excess paste is gelatinous but not fully set.
   b. Carefully trim/skim flash with a #12 blade.
   
5. Light-cure each surface of the restoration for 40 seconds or longer.
   

1. Sandblast internal metal surface of restoration for 1-2 seconds. Rinse with water and air dry.
2. Apply 1 coat of OS/OS+ to the internal metal surface. Dry with air syringe.
   

1. Mix an equal amount of Base and Catalyst Pastes and line the inside surface of the restoration.
   Optional: Adjust the viscosity with small addition of LIGHT-CURED VISCOSITY MODIFIER.
2. Seat the restoration with gentle passive pressure.
3. Remove excess paste from margins immediately.
   Technique tip:
   a. Tack-cure each margin for 4-7 seconds or until excess paste is gelatinous but not fully set.
   b. Carefully trim/skim flash with a #12 blade.
   

STORAGE: Store at room temperature (22°C/72°F). Refer to individual component labels for specific expiration dates.

PRECAUTIONS: Unpolymerized resins may cause skin sensitization in susceptible persons. In case of contact with the skin, wash thoroughly with soap and water. Hydrofluoric acid of Porcelain Etchant is a severe eye irritant and tissue irritant. If accidentally splashed into the eye, flush with a copious amount of water and seek medical attention immediately. In case of contact with other tissues, rinse spills immediately with a copious amount of water for several minutes. Injury may result if etchant is allowed to remain on the skin or mucosa for extended periods of time.

HOW SUPPLIED:

ILLUSION STARTER KIT                     C-3250K
1 Syringe Dual-Cured Clear Catalyst Paste (4g), 3 Syringes Light-Cured Base Paste Shades Opaque, Milky and Clear (4g ea.), 3 Syringes Water-Soluble Try-in Paste Shades Opaque, Milky and Clear (3g ea.), 1 Bottle ONE-STEP PLUS (2ml), 1 Bottle Porcelain Primer (3ml), 1 Bottle Porcelain Etchant (3ml), 1 Bottle 32% UNI-ETCH (1.5ml), Technique Cards, Instructions/MSDS

ILLUSION ACCESSORY KIT                  C-3270K
1 Syringe Light-Cured Color Modifier Paste (1.5g), 1 Syringe Water-Soluble Color Modifier Try-In Paste (1.5g), 1 Syringe Light-Cured Pink Block-Out Paste (1.5g), 1 Syringe Water-Soluble Pink Block-Out Try-In Paste (1.5g), 1 Bottle Light-Cured Viscosity Modifier (6ml), Instructions/MSDS

REFILLS:

WARRANTY: Subject to the provisions of the following paragraph, Bisco, Inc. recognizes its responsibility to replace products if proven to be defective. Bisco, Inc. does not accept liability for any damages or loss, either direct or consequential, stemming from the use of or inability to use the products as described. Before using, it is the responsibility of the user to determine the suitability of the product for its intended use. The user assumes all risk and liability in connection therewith.

ILLUSION is designed to be used as a system. The use of products not included in the ILLUSION system has not been evaluated by BISCO and therefore the clinical implications are unknown. The use of products outside of this system may make this warranty null and void.

* ILLUSION is a trademark of Bisco, Inc. ONE-STEP, UNI-ETCH, and ALL-BOND are registered trademarks of Bisco, Inc. PRE-BOND is a trademark of Bisco, Inc.

CAUTION: U.S. Federal law restricts this device to sale by or on the order of a dental professional.

BISCO, INC.
1100 W. Irving Park Road
Schaumburg, IL 60193
847-534-6000
1-800-BIS-DENT
www.bisco.com

CE ADMINISTRATOR
Bisico France -
Mr. Fred Picavet
L'Opera- BP. 60
13680 Lancon De Provence
France
Phone: 33-490-42-9292
Fax: 33-490-42-9261

IN-075R1
Rev. 12/03