1. Thoroughly clean the teeth to be bonded with pumice in a rubber cup or bristle brush. Take care to avoid irritating the gingival tissue since slight bleeding may cause contamination that could affect the quality of the bond.

2. Rinse thoroughly with plenty of water. Isolate the teeth and dry with the air syringe.

3. Dispense Liquid Etchant into a mixing well. Dab etchant for 20-30 seconds on the surfaces to be bonded.

4. Rinse etched teeth thoroughly to remove all traces of acid. Re-isolate and dry teeth to be bonded. The etched areas should appear chalky-white. If not, reapply etchant for an additional 30 seconds. Rinse and dry again.

5. Brush a thin coat of ORTHO-ONE No Mix Primer on to each etched and dried tooth surface to be bonded. The thin primer coat should be confined to the etched area. To avoid evaporation, do not dispense primer prematurely.
NOTE: When using no-mix bonding systems, bracket bases should closely conform to the tooth surface to be bonded. Adjust bracket base as needed.

6. Brush a thin coat of ORTHO-ONE No Mix Primer on the underside of the bracket base. Do not contaminate primed surface of bracket base. Primed surfaces should not be exposed to air for more than 10 minutes. If primed bracket base should become contaminated with saliva, etc., clean primer from bracket base with alcohol or acetone, rinse and dry bracket thoroughly. Then apply primer again.

7. Apply a thin layer of ORTHO-ONE No Mix Paste to the underside of the bracket base and immediately place bracket on tooth with a slight rotating motion. Immediately position the bracket to desired angulation and press firmly to insure paste is in a thin uniform layer. All adjustments to brackets must be made within 20 seconds (prior to gelation of paste). Remove excess adhesive from the periphery of the bracket base after the brackets are in place. Keep teeth isolated for approximately 3 minutes. Archwires may be placed 7 minutes after bracket is placed on the tooth.

8. To re-bond a lost bracket, all adhesive must be removed from the tooth, then follow steps 1-7.

ORTHO-ONE will bond to plastic brackets without additional conditioners. Follow steps 1-7, however, allow the ORTHO-ONE No Mix Primer to remain on the plastic bracket for 1 minute before applying ORTHO-ONE No Mix Paste.

Brackets and adhesive removal may easily be accomplished with pin and ligature cutting pliers or other de-bonding devices. Tooth surfaces may be further cleaned with scaling instruments and polished with rotary instruments.

HOW SUPPLIED:

STORAGE: Store at room temperature (22°C/72°F). See individual component labels for specific expiration dates.

PRECAUTIONS: Unpolymerized resins may cause skin sensitization in susceptible persons. In case of contact with the skin, wash thoroughly with soap and water. Phosphoric acid is a severe eye irritant. In case of eye contact flush with plenty of water and get medical attention. Avoid contact with skin and mucous membrane with phosphoric acid. In case of contact, flush immediately with water.

WARRANTY: Bisco, Inc. recognizes its responsibility to replace products if proven to be defective. Bisco, Inc. does not accept liability for any damages or loss, either direct or consequential, stemming from the use of or inability to use the products described. Before using, it is the responsibility of the user to determine the suitability of the product for its intended use. The user assumes all risk and liability in connection therewith.

* ORTHO-ONE is a trademark of Bisco, Inc.

BISCO, INC.
1100 W. Irving Park Rd.
Schaumburg, IL 60193
U.S.A.
847-534-6000
1-800 BIS-DENT
www.bisco.com

CE ADMINISTRATOR
Bisico France
Mr. Fred Picavet
L'Opera- BP. 60
13680 Lancon De Provence
France
Phone: 33-490-42-9292
Fax: 33-490-42-9261

IN-015R2
Rev. 2/05